Dynapar - Rotary Feedback products. Innovation, Customization, Delivery.

Dynapar
Innovation, Customization, Delivery

Dynapar encompasses the broadest line of trusted brands in motion feedback control, including Dynapar encoders and Hengstler brand incremental encoders and absolute rotary encoders, Northstar heavy-duty magneto-resistive and Heavy-Duty optical encoders and high-performance Harowe brand resolvers. Only Dynapar feedback solutions offer these world-class rotary feedback brands from one Global Supplier with 3 day delivery on most models for customer peace of mind.

Joliet Technologies is the preferred Dynapar Integrator for the Chicagoland area.


RIM Tach 6200 Digital TachometerRIM Tach® 6200 Digital Tachometer

Quick Specs…

  • Foot mounted or with accessory bracket it is ideal for close coupled, belt, or wheel driven setups
  • Extra severe duty bearings for a longer encoder life
  • Stainless steel and cast iron construction
  • Resolutions up to 2048 PPR with optional index pulse

Overview / Design Principle:

Featuring rugged, mill duty construction, the durable RIM Tach® 6200 was designed for hostile environments. The mill duty, cast iron construction of the 6200 accepts stainless steel sensor modules with patented magnetoresistive technology. The outputs are available as either single or dual outputs and are completely isolated from one another. The modular design features extra severe duty bearings (1.875” OD) to ensure longer life under heavy loads.

The patented Magnetoresistive technology of the Rim Tach® 6200 is incorporated into a heavy duty, one piece sensor module, with encapsulated surface mount electronics. These advanced modules are immune to common mill contaminants (water, oil, grease, dirt, shock, and vibration) and overall harsh environments. This state-of-the- art technology allows for much higher resolutions providing resolutions up to 2048 pulses per revolution. With the addition of a RIM Tach® Shaft Grounding Brush, induced shaft currents “drain” away, preventing premature material weakening of large AC and DC motor bearings, and their consequent failure.

Standard mill duty latching connectors provide ease of installation. These sealed connectors are simple to wire by inserting the stripped conductor in the plug and tightening the screw terminals. There is no need to field solder or to struggle with a crimp pin. The unit easily mounts on a standard NEMA 56 C face (4.5”) and requires no gap adjustments. The sensor module is very easy to change, just remove four screws and slide the new sensor module in place.

Features and Benefits:

  • Rugged Mill Duty Construction
  • Easy Installation
  • Reliable Magnetoresistive sensor unaffected by common contaminants
  • Sensor modules for fast and easy field service

Applications:

The RIM Tach® 6200 is specifically designed to meet the needs of process industries, providing the most reliable, mechanical, electrical, and environmental features available in digital tachometers today.

Specifications:

Standard Operating Characteristics

Code: Incremental
Pulses per Revolution: 60-2048
Phasing Sense: A leads B for Counter-Clockwise rotation (CCW) viewing encoder-mounted end
Quadrature Phasing: 90° ± 22°
Symmetry: 180° ± 54°
Index: 270° gated to falling B edge

Electrical

Input Voltage Requirement: 5-15 or 15-26 Volts DC
Current Requirement: With Electrical Option L: 45 mA typical per sensor module plus line driver load
With Electrical Option R: 65 mA typical per sensor module plus line driver load
With Electrical Option 5: 65 mA typical per sensor module plus line driver load
Output Signals: With Elec Option L: 5-15 V Line Driver, 150mA
With Elec Option R: 15 V Line Driver, 150mA
With Elec Option 5: 5V Line Driver, 150mA
Frequency Response: 0 – 120kHz Data & Index
Electrical Immunity: 2kV ESD, Reverse Polarity, Short Circuit
Connector: 10 pin industrial duty latching, sealed NEMA 4 &12, IP65

Mechanical

Shaft Speed: 7,000 RPM
Mounting Configuration: 4.5”

[115mm] diameter, 56 C motor face or accessory flange to meet NEMA MG1-4 standards;
foot mount with 4 slotted bolt holes
Housing Material: Cast Iron/Stainless Steel
Acceleration Rate: 3600 rpm/sec max
Shaft: 0.625”[16mm] diameter with 1.87”[48mm] long, 3/16”[5mm] square-parallel key.
Optional double ended shaft and optional 14 mm shaft with metric key
Axial/Radial Loading: 50 lbf axial, 50 lbf radial

Environmental

Operating Temperature Range: -40°C to +70°C
Storage Temperature Range: -40°C to +120°C
Humidity: to 98% RH (non-condensing)
Shock (Sensor Module): 1 meter drop test, 30 G’s Min
Vibration: 18 G’s @ 5-2000 Hz spectrum

Available Specifications:

Related Products & Resources:


For additional information or to receive a full-line catalog, contact your Dynapar representative at 1.800.873.8731 or visit their web site at: www.dynapar.com
Headquarters:1675 Delany Road • Gurnee, IL 60031-1282 • USA
Phone: 1.847.662.2666
Fax: 1.847.662.6633
Email: custserv@dynapar.com or dynapar.techsupport@dynapar.com
© 2009 Dynapar Corp. Printed in U.S.A. • Feedback Quick Reference Guide P/N# N-FLB130 (11/09) 5M


Call Joliet Technologies TODAY 

If you have any questions concerning Dynapar products, feel free to contact us:
Phone (815) 725-9696,
Toll Free (866) 492-9888,
Fax (815) 725-9393 or
E-mail info@joliettech.com


Joliet Technologies custom packages, integrates and engineers AC Variable Frequency Drives (VFD), DC Variable Speed Drives (VSD) and AC Drive Controllers using top of the line manufacturers, like ABB, Emerson-Control Techniques, Siemens and Saftronics (Fincor). Our custom drive packages are built to your specifications for your application. We specialize in large horsepower drive systems (500Hp and above). Call us at (815) 725-9696 or fax us at (815) 725-9393 or e-mail us or fill out an RFQ with your requirements. Serving the greater Chicagoland area and the World.